Key takeaways
- Compare the best awls for woodworking layout: scratch awls, a square-blade birdcage awl and a carbide scribe, with blade, handle and steel specs.
What's inside
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
Home › Uncategorized › Best Awls for Woodworking: Scratch and Birdcage Picks

- Top Pick: Narex Square Blade Birdcage Awl 874710
- Runner-up: General Tools 818 Hardwood Handle Scratch Awl
- Also consider: DASCO PRO 431-0 Scratch Awl
Table of Contents
- Why an Awl Beats a Pencil for Layout
- Narex Square Blade Birdcage Awl 874710
- General Tools 818 Hardwood Handle Scratch Awl
- DASCO PRO 431-0 Scratch Awl
- Malco A2 Large Grip Scratch Awl
- General Tools 88CM Tungsten Carbide Scribe and Magnet
- How to Choose an Awl for Woodworking
- FAQ
- Conclusion
- Product and ASIN Reference
Why an Awl Beats a Pencil for Layout
For precise joinery layout, the best awl for woodworking is the one whose point matches the job: a round scratch awl for scribing lines and spotting centers, or a square birdcage awl when the point also has to cut a small starter hole. A pencil line has real width, and a saw or chisel can drift to either side of it. An awl leaves a narrow groove or a single dimple, so the edge of a chisel can register in the mark itself and a drill bit starts exactly on the intersection of two scribed lines instead of skating across the surface.
The five tools below cover the main forms a bench awl takes. They include two traditional handled scratch awls for general layout, a one-piece forged awl built for rough handling, a large-grip awl with a stouter blade for bigger starter holes, a Czech-made square-blade birdcage awl that cuts as it twists, and a tungsten carbide scribing point for marking dense hardwoods and other hard materials. Each entry is described from published specifications, including blade profile, blade length, steel type and handle construction, so the differences are easy to compare before choosing.
As an Amazon Associate, we earn from qualifying purchases.
Narex Square Blade Birdcage Awl 874710
The Narex 874710 is the specialist of this group: a birdcage awl whose blade is ground to a square cross-section that tapers to a point. Where a round point only pushes wood fibers aside, the four edges of the square point cut them, so pressing and twisting the tool bores a small, clean starter hole. That makes it the natural pick for starting screws in hardwood without splitting thin stock, and for marking drill centers that stay put when the bit comes down.
Narex makes the blade from chrome-manganese alloyed steel with a black surface treatment, and the handle is stained, varnished beech held together with a traditional steel ferrule. The proportions are compact, with a blade of about three and a half inches in a handle of about two and a half inches, which keeps the point close to the hand for control during fine layout on dovetails, mortise and tenon work, and veneer or marquetry patterns. As a premium-tier tool it costs more than a plain scratch awl, but it is the only design here that both scribes and cuts.
Specs:
- Type: Birdcage awl, square tapered blade
- Blade material: Chrome-manganese alloyed steel, black finish
- Blade length: About 3-1/2 in
- Handle: Stained and varnished beech wood, steel ferrule
- Model: 874710
- Made in: Czech Republic
General Tools 818 Hardwood Handle Scratch Awl
The General Tools 818 is the classic bench scratch awl pattern, built for scribing layout lines and starting screw holes in soft materials. Its alloy steel blade runs the full length of the handle and is fastened to both a plated steel ferrule and a cap, a through construction that lets the tool take palm pressure and light mallet taps without the blade driving deeper into the wood.
The handle is contoured and fluted hardwood, a shape that gives fingers a positive grip when the point is dragged along a straightedge and keeps the tool from rolling when it is set down. At six and a half inches overall, it sits in the middle of the size range here: long enough for a full-hand grip, short enough to keep the point steady for fine work. This is a mid-range pick that suits a first awl for general layout, and the round point parts fibers cleanly for lines that a pencil cannot match for width or permanence on the workpiece.
Specs:
- Type: Scratch awl, round tapered point
- Blade material: Alloy steel, through-handle construction
- Overall length: 6-1/2 in
- Handle: Contoured, fluted hardwood with plated steel ferrule and cap
- Model: 818
- Best for: Scribing lines, layout work, starting screw holes in soft materials
DASCO PRO 431-0 Scratch Awl
The DASCO PRO 431-0 takes the opposite approach to handle construction: there is no separate handle at all. The whole tool is one piece of drop-forged high carbon steel, seven inches long, with a knurled grip section turned into the shank. Nothing can loosen, split or pull off, which makes it the budget-tier choice for a shop awl that gets tossed in a tool bag or used for rougher jobs like marking on site lumber.
The round point scribes and starts holes in wood, metal and leather, and the one-piece forging means the point can be resharpened on a stone or file for the life of the tool. The knurling gives purchase when hands are dusty, and the full steel body tolerates being struck or pried with in ways a wooden handle should not. Woodworkers who want a traditional feel will prefer a handled awl, but for durability per dollar this design is hard to beat, and it is assembled in the USA.
Specs:
- Type: Scratch awl, round point
- Construction: One-piece drop-forged high carbon steel
- Overall length: 7 in
- Grip: Knurled steel grip section
- Model: 431-0 (VN74310)
- Origin: Assembled in the USA
Malco A2 Large Grip Scratch Awl
Malco builds its scratch awls for the sheet metal trade, but the A2 translates well to the wood shop, especially for anyone who finds standard handles too slim. It pairs a large grip handle with the stoutest blade in this roundup: a quarter inch in diameter and four inches long. That extra blade stock makes the A2 the pick for deeper, wider starter holes and for marking jobs where a fine point would flex or wander.
The overall length is six and a quarter inches, so despite the heavier blade the tool stays compact and controllable. Malco manufactures the A2 in the USA, and the blade is a plain, resharpenable steel point rather than a coated one, which keeps maintenance simple: a few strokes on a fine stone restore the tip. In tier terms it sits in the mid-range, above basic one-piece awls and below the specialty birdcage and carbide tools, and it suits larger hands or users who routinely start holes for bigger screws and lag hardware.
Specs:
- Type: Scratch awl, round point, large grip
- Blade diameter: 1/4 in
- Blade length: 4 in
- Overall length: 6-1/4 in
- Handle: Large grip handle
- Model: A2
- Made in: USA
General Tools 88CM Tungsten Carbide Scribe and Magnet
The 88CM is the layout point to reach for when a steel awl point dulls too quickly. Its working end is a tungsten carbide tip, the same class of material used on cutting tool edges, and it is rated for marking hardened steel, ceramic and glass as well as wood. On dense, abrasive hardwoods and on end grain, a carbide point keeps scribing a clean line long after a plain steel point has rounded over.
The tip is replaceable, so when it eventually wears, the point can be swapped instead of replacing the whole tool. A magnet built into the opposite end picks up small screws, pins and filings, which is handy at the bench when hardware is being marked and fitted. This is a premium-tier pick and a different feel from a handled awl: it is a slim scribing instrument rather than a tool for boring starter holes, so it complements a scratch awl instead of replacing one. Pair it with any handled awl above and both scribing and hole-starting are covered.
Specs:
- Type: Scriber with replaceable point
- Tip material: Tungsten carbide, replaceable
- Marks: Hardened steel, ceramic, glass, wood and plastic
- Extra feature: Built-in magnet in the end of the body
- Model: 88CM
- Best for: Fine layout lines on hard and abrasive materials
How to Choose an Awl for Woodworking
Start with the point profile, because it decides what the tool can do. A round scratch awl point scribes lines and pricks center dimples, and it is the right default for general layout. A square birdcage point adds cutting edges, so it can bore a small starter hole by twisting, which matters in hardwood and thin stock where a pushed round point can split the grain. A bradawl, with a flat chisel-like tip, is a third pattern worth knowing about, though none of the picks above use it.
Blade length and diameter come next. Blades around three and a half inches keep the point close to the hand for controlled scribing against a square or straightedge. Longer or thicker blades, like the quarter-inch blade on the Malco A2, trade some finesse for the ability to start bigger holes without flexing. Handle style is the third factor: a fluted hardwood handle with a steel cap tolerates mallet taps, a cushion or large grip suits long sessions and bigger hands, and a one-piece forged body removes the handle as a failure point entirely.
Finally, consider the material being marked. For softwoods and general bench work, any alloy or high carbon steel point holds up well and resharpens easily. For dense hardwoods, abrasive composites or occasional marking on metal and tile, a carbide point such as the General Tools 88CM keeps its edge far longer. Many benches end up with two tools, one handled awl for starting holes and one fine point for scribing, rather than one tool asked to do both jobs.
FAQ
What is the difference between a scratch awl and a birdcage awl?
A scratch awl has a round point that parts wood fibers, which makes it ideal for scribing layout lines and pricking center marks. A birdcage awl has a square tapered point whose edges cut fibers as the tool is twisted, so it can also bore a small starter hole. The Narex 874710 above is a birdcage pattern; the other handled picks are round-point scratch awls.
Can an awl replace a pilot hole for screws?
For small screws in softwood and many hardwoods, yes: pressing and twisting an awl makes a starter hole that guides the screw and reduces the chance of splitting, especially near the end of a board. For large screws, lag hardware or very dense species, an awl mark should be followed by a drilled pilot hole, using the dimple to keep the bit from wandering.
How do you scribe an accurate line with an awl?
Register the awl point in the notch of a square or against a straightedge, tilt the tool slightly toward the direction of travel, and draw it along the edge with light, even pressure. A shallow first pass followed by a firmer second pass in the same groove gives the cleanest line, and that groove then guides a saw or chisel edge at the start of the cut.
How should an awl point be maintained?
Wipe the blade clean after use and store the tool so the point cannot strike other tools or the bench. When a steel point dulls, restore it by rotating the blade against a fine sharpening stone at its original taper until the point is keen again. Carbide tips such as the one on the General Tools 88CM are not resharpened this way; they are replaced when worn.
Conclusion
Every awl in this roundup will out-mark a pencil, but the right choice depends on the work. The General Tools 818 is the balanced default for scribing and layout, the DASCO PRO 431-0 is the budget pick that shrugs off rough handling, and the Malco A2 adds blade size and grip for bigger starter holes. The Narex 874710 birdcage awl is the premium choice when starter holes in hardwood are part of the layout routine, and the General Tools 88CM carbide scribe covers fine lines on the hardest materials. Pick the point profile first and the rest of the decision follows from it.
Related guides
Keep reading
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.






Write Your Review
No reviews yet. Be the first to share your experience!